Friday, February 1, 2013

DIY Bar Cart

Allen Lau shares the how-to for a charming bar cart made of scrap wood. Not only does this new piece of furniture hold alcohol, it stores stemware, adds character to our dining room, and makes happy hour happen more!

What should one do with an old pile of  Ikea mattress support slats weathered by the elements, taking up space in the side yard collecting dirt and harboring critters? Turn it into a bar cart.

BEFORE
AFTER
Start by detaching all the slats from the ribbon strips and remove any staples. Then create frames for three trays. The slats I had were 2½" x 38" x ¾". I roughly estimated the amount of material needed, keeping in mind to leave some for the vertical supports and some braces. Also, in order to minimize the number of cuts, I decided to keep the length of the slats intact and build the cart trays based on that. So I came up with the following requirements for building each tray:
  • 6 slats for the bottom of the tray--no cuts, yeah! Using six slats works out nicely so that standard wine bottles fit across the tray if you want to lay them flat.
  • 2 slats for the front and back of the tray with 45° cuts at the ends
  • 2 slats for the left and right sides of the tray; cut these to 15" length and then make 45° cuts at the ends
  • 2 slats for securing the bottom slats; also cut these to 15" length (no angled cuts for the ends)
I used only a miter box saw and some elbow grease to make all the cuts. So the alignment for the frames turned out slightly off in some cases, but weren't too bad. If you have a power saw, I highly recommend using that instead to make more precise cuts.

Make 45° angled cuts at the ends

Glue and nail angled ends together to form rectangular frame

With some wood glue and small finishing nails, assemble the frame of the tray into a rectangle, fitting together the 45° angled cuts. Once you have a rectangular frame, lay the 6 slats down on the frame from edge to edge. Secure the slats to the frame with some wood screws. (I recommend pre-drilling holes for the screws to prevent splintering. But if you don't mind some splintering and like a more rustic look, skip the pre-drilling, or use nails instead of screws.) Place the two 15" slats across the bottom slats, 10" from the edges. Secure to the bottom slats.



Now, repeat and make two more trays. With three trays done, take a break, go outside, get some fresh air, and spend some time with the family so your spouse doesn't complain that you are neglecting them.

Okay, let's wrap this up. For the vertical supports cut 4 slats to lengths of 36". I decided to lop off a couple inches from the 38" slats so that the cart wouldn't end up too high since the wheels add another couple inches to the height of the cart.

Lay the trays on their sides so that you can place two of the support slats across the three trays. Imagine placing the finished cart in the picture onto its back or front. Secure the slats to the trays using the bottom braces of the trays as guides for the supports. The ends of the braces should line up perpendicular to the vertical slats.

Position the middle tray such that you leave enough room for a standard wine bottle (about 12") to be placed standing up in the tray. In this case, the lower tray bottom to the underside of the tray above is 15¼".

Carefully, flip entire assembly over to the opposite side and repeat with the other two vertical slats. So the cart is basically done. Time to add some reinforcement so that it can hold up all your precious booze. Measure and cut braces to fit from the underside of an upper tray to the top of the tray lip. Place and secure this brace right behind the vertical support slat. Repeat adding this vertical bracing another seven times for a total of eight braces--four for between the top and second trays and four for between the second and bottom trays.

The cart should now be very secure and sturdy. Flip the cart over so that it is upside down with the top tray facing down. Measure and cut to length two slats to fit across the bottom of the cart so that they just cover the ends of the bottom of the vertical support slats. (See picture below with the wheel.) Secure the two final bottom slats. Screw in the 2" caster wheels onto the ends of the bottom securing slats.



Vertical brace between an upper and lower trayAnother view of the vertical brace, doubling up for the outer vertical support slat

Lockable 2" caster wheel. Notice the securing slat sitting just above the wheel, allowing the end of the vertical support to rest on top.Optional hanging rack for glasses

Congratulations! You now have a bar cart made by your very own hands and saved yourself several hundred dollars along the way.


Total cost of this project was about $30 for wood screws and four lockable caster wheels. (Ikea slats were $20 per bundle; I used two bundles here. I'm not counting the cost of these since they were "junk" sitting outside in the yard.) 

Total time invested was about one weekend.

I was inspired by this Collins bar cart from Crate and Barrel

You may want to add your own flourishes to the cart. How about adding a hanging rack for glasses or staining the cart your favorite color? Please share your creations.

6 comments:

  1. This looks great. One question...how are the slats for holding the stemware secured to the cart? Did I miss that part?

    Great work. Thank again.

    ReplyDelete
  2. @randalls, picture a giant comb. Use one slat (A), placed perpendicular to the stemware slats(B), securing each of these slats(B) at one end to the perpendicular slat (A). Then the whole assembly can be screwed to the underside of the top tray. The perpendicular slat (A) provides the necessary gap between the top tray and the stemware slats(B) to accommodate the bases of the hanging glasses. Hope this helps.

    ReplyDelete
  3. This looks absolutely wonderful! I'll just made myself a dining table and want a bar cart to match. I'll be making this next weekend. Very impressive!

    ReplyDelete
  4. love this. Can I buy the slats at Ikea or do I need to go Home depot??

    ReplyDelete
  5. Yes, you can buy the slats from Ikea; but really any similarly sized plank would work fine.

    ReplyDelete
  6. Are these slats still available from Ikea? I can only find the SULTAN LADE (http://www.ikea.com/us/en/catalog/products/60079788/) bed base which are only 27 ½" long. I know I can just buy a bunch of 1x3" lumber but the Ikea slats are nice because they are already cut, routed, and sanded.

    ReplyDelete